Welcome to the Duct Cleaners' Supply online store.Please register to place your order.If you have any questions please call us at 800.634.2822 We have the tools and experience to help you get the job done! MICROLINE ®/ HYDRA / ECO-Whip TubingIs that a snake nearby or just your airlines? Leaking airlines slow you down, waste energy and may drip condensation in your customer's home. As you look at the images of the coupler and plugs, do you notice anything? Most people think the problem is with the coupler. The sealing area of the coupler is INSIDE the body of the coupler. If that is the case, How can you damage it? Even if you drag it around on pavement the sealing zone won't be touched.There is normally an o-ring which seals between the coupler and the plug. With good quality components this o-ring is usually very durable and should give a long service life. So how can the problem be with the coupler? Well most times it's not. When you are handling your airlines what part is subject to damage and wear?

The area that seals against the o-ring can get scratched or dented very easily under normal working conditions. Imagine two surfaces closing tightly against each other. No gaps just a good seal. If you scratch or gouge one of the surfaces you have an area where something can get through. Kind of like digging a hole under a fence. You have a void where something may get through. How to deal with this? Keep an eye on the plugs on your airlines. They can cut or scrape the o-rings if the get scratched or worn. When wrapping up air lines keep the plug end in your hand. When you have it coiled put the plug into the coupler and lock it together. There are o-ring lubricants designed to keep them lubricated and sealing well. Many manufacturers recommend silicone based products. Petroleum based products may harm the o-rings. If you see a plug that is damaged or worn , replace it. Making sure you get the maximum air from your compressor will save you time and help keep you profitable. Viper Clean Sweep System ..

There were issues of poor airflow within the building and the temperature set point was difficult to reach and then maintain. There had been external assistances where engineering changes had been made to the cooling system to increase the cooling capacity across the face of the coil in order to produce cooler air. TVH were contacted to provide advice of the systems performance. Upon inspection of the supply air ductwork, the air stream was found to be restricted due to turning vanes within the system were found to be dislodged and leaning up against another set of turning vanes within the supply air system. The building is a single storey establishment which operates 24/7. The building is predominantly sealed and is solely reliant on the air conditioning system for air distribution within the occupied space. There is only one air conditioning plant located in a dedicated plant room. The air conditioning is a large Air Handling Plant serviced by a chilled water system. The return air and outside air intakes are ducted directly into the Air Handling Unit.

The building is located in the Southern Australia Zone (BCA Zone 7). In order to return the system back to full operational use the following items were undertaken;best leather cleaner for beige car seats The duct cleaning works were completed during night shift to minimise disruption to the operation of the building. laptop fan dust cleanThe number of TVH staff on site was increased to reduce the total number of days that access to the system was required.top-rated vacuum cleaners under $150 The dislodged turning vanes were removed and new ones installed into the correct position. bridge home services duct cleaning

Due to the amount of dust and debris located in the ductwork it was a requirement that all ductwork downstream of the turning vanes be cleaned. vacuum cleaners best affordableWhen there is restricted air flow the number of dead air zones within the supply air system increase and therefore allows dust, debris and other contaminates to enter the system. best way to clean grease from range hoodIf the turning vanes had been reinstated without cleaning the likelihood of contaminates become airborne when the system was reinstated was almost certain. It’s important when conducting any mould works within a building that it is conducted according to the IICRC S520 International Best Practise Guideline. Once a mould event (outbreak) has occurred it is important that all items with the space are remediated or a detail clean is conducted (dependant on the severity of contamination) to ensure that the entire space can be brought back to normal ecology, pre-existing conditions before the fungal activity.

Flexible Duct Supply Air - Before Flexible Duct Supply Air - After Solid Supply Duct – Before Solid Supply Duct – After Solid Supply Air Duct – During CleaningThe scenario: You get a flyer in the mail from a company offering to clean the air ducts at your home for only $99. Intrigued by the low price, you contact the company and set up an appointment. When the company arrives at your house, the rep tries to sell you on a bunch of other services, including carpet cleaning or mold remediation, to improve the air quality inside your home. If you don’t bite at these invoice-increasing items, he gives your ducts a cursory cleaning before moving on to the next mark somewhere in your area. That lowball offer should have been a red flag to avoid that firm. A reputable company will charge $400 to $1,000 to clean the ducts in a typical 2,000-square-foot house, says the National Air Duct Cleaners Association (NADCA). A quality job should take two pros, who’ll use specialized tools, about 8 to 15 hours to complete.

Even more important to know is that there’s no proof that cleaning ducts prevents health problems, according to the U.S. Environmental Protection Agency. Nor do studies conclusively show that dirty ducts increase levels of airborne particulates in a home. Still, there are times when you should get your ducts cleaned:• Have the ductwork cleaned if it contains visible mold buildup or has debris coming out of supply registers, or if the ducts are infested with vermin. Check for problems by removing the registers and shining a flashlight into the ductwork.• Consider having your ductwork professionally inspected if someone in your home is suffering from unexplained allergies or illness. Before you do that, however, a doctor should rule out other causes. To find a reputable duct cleaner, get referrals from the company that services your furnace. You’ll also find NADCA member contractors in your area on the association’s Web site. Before you sign a contract, ask for evidence of contamination, including a lab report if mold is a concern.