How to clean fan in Toshiba Satellite P305D In this guide I explain how to clean the cooling fan in a Toshiba Satellite P305D laptop. Also this guide should work for the following Toshiba models: Satellite P300, Satellite P300D, Satellite P305. My customer complained that his computer overheats and shuts off while running a game. Apparently, the heat sink got clogged with dust and needed a good cleaning. There is no easy access to the cooling fan in a Satellite P305D. You can see the fan grill on the bottom but the fan is covered with a perforated metal sheet. Blowing air into the grill will not be enough for cleaning the cooling module. You can get better access to the fan under the keyboard. Let’s remove the keyboard. Remove three screws located in the battery compartment. Carefully lift up and remove the keyboard bezel. Remove two screws securing the keyboard. Lift up the keyboard and place it upside down on the palm rest. It’s not necessary to disconnect the keyboard cable from the motherboard.

The cooling fan is still covered  but at least now you can blow air into the fan and remove all dust from the cooling module.Blow air into the cooling fan through two holes on the top cover.Change the direction and blow air into the fan grill on the side. Also, blow air into the air intake on the bottom. Change air direction two-three times until there is no dust coming out of the laptop. You can support my work!Toshiba Satellite A215 S4697 Fan Replacement Be an action hero! This guide needs images that better demonstrate how to perform specific actions. A few more images would make this guide's procedures crystal clear. This guide needs better markups. Help out by correcting or making some markup annotations. This guide has been the hard work of our awesome students and is found to be exceptionally cool by the iFixit staff. When your computer heats up and runs loudly, it may need some new fans to keep the runnin' machine cool.This guide will teach you how to get to the fans inside your laptop and replace them.

Just make sure to keep track of your screws! Close the laptop and turn it over so that the base is facing upwards and the spine is facing away from you.pro clean duct and carpet service Find the battery compartment.air duct cleaning service nj Slide the left slider which is just beneath the battery compartment into its leftmost position.air duct cleaning service nj Slide and hold the right slider into its rightmost position. best vacuum cleaner 2012 europeLift the battery out of the compartment.best way to clean dog urine from leather couch

Do not touch the gold nodes inside the compartment. Place laptop right side up on a flat and clean surface. the best way to clean wooden venetian blinds Find the strip just above the keyboard and locate the gaps behind the F1, F8, and Insert keys. Remove the strip by sticking your plastic opening tool into these gaps in order, and pulling up. Locate the two 2.3mm Phillips #1 screws at the top of the keyboard that attaches the keyboard to the frame behind it. Find the latch above the F8 key that overlaps the keyboard. Use a plastic opening tool to press the key board's tab downward, until the key board is released. Pull the keyboard out by shifting it forward towards the screen and pulling up. CAUTION: Do not pull it out all the way yet. It is still attached to the laptop by a cable. Find the ribbon cable that connects the keyboard to the laptop.

Look for the black tabs on both sides of cable at the laptop end of the cable. Using a pair of tweezers, pull the black tabs on both sides of the cable connector towards the screen until the cable can be pulled out easily. Pull out the cable and completely remove the keyboard. Turn computer over so that the battery compartment is facing up and is at the top. Locate and unscrew one captive Phillips #1 screw located at the center. A captive screw cannot be completely removed from the device's component. Use a plastic opening tool to open the motherboard access cover. Do not touch the motherboard. Remove one 1.5mm Phillips #1 screw located near the top left edge of the opening. Flip your device right side up, and rotate it so that the optical drive is facing you. Insert a paper clip into a manual release switch located to the right of the automatic release button. Optical Drive will not release if you insert the clip diagonally. Make sure to insert the clip straight into the switch.

Gently pull out the disk drive until you can see the metallic case of the optical drive. Hold the metal case and continue to pull the drive out toward you. Once you see the yellow labels on the disk drive, fully retract the disk mount until you hear a click. Continue to pull the disk drive toward you until it is completely removed from the laptop's housing. Close the lid and flip the laptop over so that the bottom side is facing you. Remove nineteen 8mm Phillips #1 screws, labeled with "F8." Locate and Remove two "f4" screws as well. Locate the RAM compartment. Unscrew the two Phillips #1 screws and lift the lid up. Note that these two screws do not detach from lid. Unscrew the two 8mm Phillips #1 screws inside the RAM compartment. Remove the three 3mm Phillips #1 screws inside the battery compartment. Turn computer over and open lid. Make sure all the screws are cleared off the device before you flip the device over.

Remove the four 8mm Phillips #1 screws in the slot where the keyboard sat. Locate the speaker cables near the top right corner. Use tweezers to carefully disconnect the cable. Locate the cable on the bottom left hand corner of keyboard slot. Gently pull it out to the left. Locate the cable at the top of the frame. Using tweezers, pull tabs on either side, toward the screen, and pull the cable out of socket. Locate another ribbon cable at the lower center of the keyboard slot. Using tweezers, pull tabs out to the left, and pull cable out of socket. Using a plastic opening tool, insert into slit around laptop and separate the silver frame from black bottom. The black lip on the front of the laptop is part of the top silver frame. Lift frame away from laptop. Locate the fan in the top left hand corner of the inside of the laptop. Remove the following screws from the fan encasement: Two 12 mm Phillips #1 screws Two 2.3 mm Phillips #1 screws.